jeff1
09-23-2013, 12:48 PM
Appliance tip of the week...
Washing Machine Dancing across Floor
Here's some tips on how to keep it in its place.
Front Load Washing Machine (http://www.repairclinic.com/Washing-Machine-Front-Load-Frigidaire-GE-Kenmore-Style-Appliance-Diagram)
Top Load Washing Machine (http://www.repairclinic.com/Washing-Machine-Top-Load-GE-Style-Appliance-Diagram)
It's very important your washing machine be perfectly level and on a solid, stable floor. Off-balance washing machines sometimes shimmy across the floor or even do a full-out jig. This dancing is often accompanied by loud banging noises. If this happens to you, here's how to fix it yourself:
Adjust the machine's leveling legs until a level (http://www.repairclinic.com/referral.asp?R=153&N=741270) shows the machine is perfectly level from front to back and side to side. While doing this, make sure the legs are adjusted up as far as possible in order to lower the center of gravity of the machine. Lubricate the leveling legs with something like WD-40 occasionally to prevent them from getting stuck in the up position.
Once the unit is level, tighten the lock nuts on the leveling legs against the base of the washer to prevent the legs from unscrewing due to washer movement.
NOTE: Some washing machines have self-leveling rear legs. If this is true of your washer, tip the machine forward and set it back down firmly to set the rear legs. Then adjust the front legs until the washer is level. You still need adjust the front leveling legs up as far as possible.
To prevent your washer from becoming off balance, don't overload it or run a very small load, with just a few heavy items. Either case can cause your machine to go off balance.
Weak floors also lead to dancing washing machines. If the floor is vibrating when the washer is spinning, the floor should be strengthened. To check your floor, set a half-full glass of water next to the washer and put it into a spin cycle. If the glass of water vibrates, the floor needs to be strengthened. A layer of ?" fire-resistant plywood that spans underneath both the washer and dryer often does the trick, screw this down to the existing floor.
If your washer slides because it sits on a slick floor, try putting specially made non-slip pads (http://www.repairclinic.com/referral.asp?R=153&N=437538) underneath the leveling legs.
421 Shake Away Plus Vibration Isolation Pads. Four 5-layer pads to reduce floor vibrations (http://www.repairclinic.com/referral.asp?R=153&N=1394226)
422 Affresh? Washer Cleaner removes and prevents odor-causing residue that can occur in all brands of HE washers (http://www.repairclinic.com/referral.asp?R=153&N=1373065)
jeff.
Washing Machine Dancing across Floor
Here's some tips on how to keep it in its place.
Front Load Washing Machine (http://www.repairclinic.com/Washing-Machine-Front-Load-Frigidaire-GE-Kenmore-Style-Appliance-Diagram)
Top Load Washing Machine (http://www.repairclinic.com/Washing-Machine-Top-Load-GE-Style-Appliance-Diagram)
It's very important your washing machine be perfectly level and on a solid, stable floor. Off-balance washing machines sometimes shimmy across the floor or even do a full-out jig. This dancing is often accompanied by loud banging noises. If this happens to you, here's how to fix it yourself:
Adjust the machine's leveling legs until a level (http://www.repairclinic.com/referral.asp?R=153&N=741270) shows the machine is perfectly level from front to back and side to side. While doing this, make sure the legs are adjusted up as far as possible in order to lower the center of gravity of the machine. Lubricate the leveling legs with something like WD-40 occasionally to prevent them from getting stuck in the up position.
Once the unit is level, tighten the lock nuts on the leveling legs against the base of the washer to prevent the legs from unscrewing due to washer movement.
NOTE: Some washing machines have self-leveling rear legs. If this is true of your washer, tip the machine forward and set it back down firmly to set the rear legs. Then adjust the front legs until the washer is level. You still need adjust the front leveling legs up as far as possible.
To prevent your washer from becoming off balance, don't overload it or run a very small load, with just a few heavy items. Either case can cause your machine to go off balance.
Weak floors also lead to dancing washing machines. If the floor is vibrating when the washer is spinning, the floor should be strengthened. To check your floor, set a half-full glass of water next to the washer and put it into a spin cycle. If the glass of water vibrates, the floor needs to be strengthened. A layer of ?" fire-resistant plywood that spans underneath both the washer and dryer often does the trick, screw this down to the existing floor.
If your washer slides because it sits on a slick floor, try putting specially made non-slip pads (http://www.repairclinic.com/referral.asp?R=153&N=437538) underneath the leveling legs.
421 Shake Away Plus Vibration Isolation Pads. Four 5-layer pads to reduce floor vibrations (http://www.repairclinic.com/referral.asp?R=153&N=1394226)
422 Affresh? Washer Cleaner removes and prevents odor-causing residue that can occur in all brands of HE washers (http://www.repairclinic.com/referral.asp?R=153&N=1373065)
jeff.