Search:

I did have it off. I measured the belt. It should be okay. Not sure about the belt debris that I saw. Maybe just wear over time. No way would I try to braze it unless I have it off the machine...

You do have a point. Might just wait and see if I can come across another. In fact I have a lead on one that needs a timer. It is not as nice as this one, but they are both older. I have another...

Heat by torch is not going to harm any seals?

Can't seem to reach the screws. That or someone has changed them.

Kinda sneaky of 'em. Hmm, might do some experimenting with this thing.

What sixe torx driver does it take to get the pump off?

Might try a heat sink and a little brazing on this thing. ...

With ot without gasoline?!

Hehe, haven't thoguht about trying heat. May have to try it.

I did try kicking it. Climbed up on it and gave it a few downward kicks.

What is stuck, tube to the...

So what if I put this thing in spin with the tub nut off the drive block? Or maybe let it agitate and hope the thing comes loose? Tried kicking it. NO luck.

Btw, I did spray with penetrating...

Took another look at this machine yesterday before I almost took it to the curb.
Anyway, the pulley on the motor shaft looks like it is slipping barely moving the tub/basket in spin cycle. Is...

That might explain making a sound when it is spinning with no water in it and no change in tempo. I kind of feel like the pump has a small amount of damage and is making a sound when empty that can...

So, 1 and 2 are not always for the heat circuit.

Thanks

Thanks , Jeff.
On these inline terminal switches, are they numbered from 1 -6 from top to bottom or bottom to top consecutively, or are 1 and 2 turned around?

Another thing, the numbers on the...

Thought I might revisit this subject. I got a chance to try this thing today for a bit. When it was just pumping the water out, it was very quiet and normal sounding. When it spins is when it...

Appreciate that. Terminal 1 is next to the top, right? Top is 2?

Violet? Dang, I seem to have a hard time remembering that color.
One of them things where you knowsomething does not seem...

Model - DDE5100SBLWW

Can't find a schematic showing the wiring on the motor for this dryer. I got them all but the Black and the Lavender.

The wires for this model are on the right side of...

Any experience with these? My opinion is not a good opinion.

Model - wtw5640xw0
Serial - C0253350
" A year old." If you don't count the three years between the year it was made and now.
...

Yeah I thought it worked like a Maytag as far as tightening. I guess the thing for me to do is measure the belt to see if it is a little too long. Along with checking the pump and tension pulley and...

Model - AWN412SP111TW01

How much slack should be in the belt on this machine? This one seems awful loose. Complaint was no spin sometimes with large loads. There is belt debris indicating a...

The head gasket shellac seems to have made a very good seal.

Sometimes it is a head scratcher.

The lady I got this washer from said she had paid $180 once on this machine when the sensor was not working right. I think maybe that was just for the part. So,...

Got that part down pat!

It was seeping out just a very little which caused rust on that corner of the frame. If I hadn't noticed the rust on that part of the frame under the hose and run my finger across the hose inlet...

Guess I will try some more penetrating fluid and a little stomping. Sometimes you just have to put your foot down! I do believe the protrusions are part of the filter as they are the same color,...

Yeah not sure it could be forced from the outside in and not have a leak.

This one had a very slow seepage. I coated it with gasket shellack and I am letting it cure good before I check it again.

Thanks, glad to know this normal. Still seems a little strange though. :)

Evidently, but is that normal?? Seems like a flaw if so.

Whats the fix?